Marshall Inline Products featured in Hot Rod Mag......

Moderator: Mod Squad

CNC-Dude
Registered User
Posts: 1391
Joined: Wed Nov 19, 2008 6:06 pm
Location: N. Ga.
Contact:

Marshall Inline Products featured in Hot Rod Mag......

Post #1 by CNC-Dude » Sun May 21, 2017 3:07 pm

Constantly trying to get inlines noticed in magazines is always a challenge, so participating with them in feature articles is always a positive sign. Here is a recent Hot Rod Magazine article that used one of my products I designed and manufacture in a series of dyno tests for an inline engine build. Its the Marshall copper intake/exhaust gasket. Here is the link to the article below:
http://www.hotrod.com/articles/slant-sickness-add-77-hp-mopar-slant-six/
Image

bmbm40
Registered User
Posts: 1075
Joined: Tue Feb 22, 2005 6:25 pm
Location: Carson City, NV

Re: Marshall Inline Products featured in Hot Rod Mag......

Post #2 by bmbm40 » Sun May 21, 2017 6:30 pm

Congratulations on your products and the magazine article.
66 Bronco-1970 250, NV3550, DSII, 4 turn ps, uncut, 1" bl, 2.5" sl, front disc, twin stick D 20, 30 x 9.50
NEXT- direct mount 1.08 on D8 head, power brakes, rear limited slip, 3G, electric fan, electric upgrades, custom curved DSII, header, 31" tires

New guy? Get the Falcon Performance Handbook and Ford six high performance parts from https://vintageinlines.com

CNC-Dude
Registered User
Posts: 1391
Joined: Wed Nov 19, 2008 6:06 pm
Location: N. Ga.
Contact:

Re: Marshall Inline Products featured in Hot Rod Mag......

Post #3 by CNC-Dude » Sun May 21, 2017 7:42 pm

Thank you!
Image

User avatar
bubba22349
Global Moderator
Posts: 8219
Joined: Sun Jan 03, 2010 4:46 pm
Location: Flagstaff, Az. 86005 near the old Route 66

Re: Marshall Inline Products featured in Hot Rod Mag......

Post #4 by bubba22349 » Sun May 21, 2017 10:22 pm

Back in the day I used to race my 223 against theose slant six'es they were quite tough. CNC Dude that's really excellent :beer: Now if we could also get the Ford 300 six recognized! :thumbup: :nod:
A bad day Drag Racing is still better than a good day at work!

I am still hunting for a project car to build but with my current low budget it's not looking so good. My Ex- Fleet of Sixes these are all long gone! :bang: 1954 Customline 223 3 speed with O/D, 1963 Fairlane project drag car with BB6, 1977 Maverick 250 with C4, 1994 F-150 a 300 with 5 speed.

drag-200stang
Registered User
Posts: 921
Joined: Sun Oct 19, 2003 6:10 pm
Location: Michigan

Re: Marshall Inline Products featured in Hot Rod Mag......

Post #5 by drag-200stang » Sun May 21, 2017 10:36 pm

Good job! :thumbup:
Had a 225 in a 66 A100 Van loved it , all torque.
66 Mustang Coupe
200 turbo w/lenco 4-spd
stock adj. rockers, stock timing set, ARP studs
best 1/4 mile ET 9.85/best mph 139 on 8 lbs progressing to 15 lbs boost
Went 9's when 10's was fast.

CNC-Dude
Registered User
Posts: 1391
Joined: Wed Nov 19, 2008 6:06 pm
Location: N. Ga.
Contact:

Re: Marshall Inline Products featured in Hot Rod Mag......

Post #6 by CNC-Dude » Mon May 22, 2017 6:04 pm

Thanks everyone, now let's see if we can get some Ford 6 exposure.
Image

Who is online

Users browsing this forum: No registered users and 3 guests