Click Here -> Please Consider Making a PayPal Contribution to the FordSix Forum!
2019 Contributors:
NJwpod, 1strodeo, mightynorseman, maxtrux, 6d7coupe, broncr, Phase3, 68Flareside240, bmbm40, mustang6, WorldChampGramp, justintendo, BigBlue94, ags290, motorsickle1130, Rooster, ousooner919, ethanperry, rzcrisis, DoctorC, jamyers, Motorboy, fastpat, Silverback280, chad, drag-200stang, THE FRENCHTOWN FLYER, Jimmys61falcon, rjonah, Sooshi, Robert92867, Invectivus


PLEASE TEST ON http://dev.fordsix.com

<<<***PLEASE READ*** New Site Update >>>

Adjustment wheel all the way out with new cylinders & shoes

Moderator: Mod Squad

User avatar
bubba22349
Global Moderator
Posts: 9766
Joined: Sun Jan 03, 2010 4:46 pm
Location: Flagstaff, Az. 86005 near the old Route 66

Re: Adjustment wheel all the way out with new cylinders & shoes

Post #51 by bubba22349 » Tue May 19, 2020 3:23 am

:hmmm: Well now we are getting somewhere I have seen this happen only a few times before. :shock: It's no wonder your having all this trouble with shoes dragging those drums were just not machined properly during their manufacture, so that after the drums are pressed on your hubs they aren't spinning in a true circle. To fix this you will need to have then turned just enough to get them round again and running true. Good luck. :nod:
A bad day Drag Racing is still better than a good day at work!

I am still hunting for a project car to build but with my current low budget it's not looking so good. My Ex- Fleet of Sixes these are all long gone! :bang: 1954 Customline 223 3 speed with O/D, 1963 Fairlane project drag car with BB6, 1977 Maverick 250 with C4, 1994 F-150 a 300 with 5 speed.

63flcn
Registered User
Posts: 48
Joined: Thu Apr 09, 2020 8:34 pm

Re: Adjustment wheel all the way out with new cylinders & shoes

Post #52 by 63flcn » Tue May 19, 2020 11:29 am

I would agree with however I have had 3 sets of drums on, the factory ones, ones from MACs and now a set from NAPA. They all drag in the same spot. NAPA told me they didnt need to be turned. I don't know

User avatar
bubba22349
Global Moderator
Posts: 9766
Joined: Sun Jan 03, 2010 4:46 pm
Location: Flagstaff, Az. 86005 near the old Route 66

Re: Adjustment wheel all the way out with new cylinders & shoes

Post #53 by bubba22349 » Tue May 19, 2020 12:39 pm

Yes for sure those brake shoes will eventually wear themselves into and conform matching the shape of the drums over a period of time and with more use, at that point you will then have your best brake operation. It all depends on how bad the problem is, if it's not draging all that bad than let it go and within that amount of time the problem will self correct. Turning the drums would just speed that all up the shoes would conform to the drums would practically be immediate. Drive it easy for awhile until everything wears into each other. Best of luck :nod:
A bad day Drag Racing is still better than a good day at work!

I am still hunting for a project car to build but with my current low budget it's not looking so good. My Ex- Fleet of Sixes these are all long gone! :bang: 1954 Customline 223 3 speed with O/D, 1963 Fairlane project drag car with BB6, 1977 Maverick 250 with C4, 1994 F-150 a 300 with 5 speed.

63flcn
Registered User
Posts: 48
Joined: Thu Apr 09, 2020 8:34 pm

Re: Adjustment wheel all the way out with new cylinders & shoes

Post #54 by 63flcn » Sat May 23, 2020 12:08 am

Adjusted the front shoes out a few more clicks.

Car was pulling to passenger or driver side for no apparent reasons. Put new rubber lines on the front and that seems to have stopped it. Also made the ENTIRE braking feel better. Pedal is smooth and consistent and braking force is predictable now.

Once the shoes wear in a little more and I get the ball joints replaced I think we will be 100%

User avatar
bubba22349
Global Moderator
Posts: 9766
Joined: Sun Jan 03, 2010 4:46 pm
Location: Flagstaff, Az. 86005 near the old Route 66

Re: Adjustment wheel all the way out with new cylinders & shoes

Post #55 by bubba22349 » Sat May 23, 2020 3:02 am

:beer: glad to hear that you are making more progress on the brakes operation. :thumbup: :nod:
A bad day Drag Racing is still better than a good day at work!

I am still hunting for a project car to build but with my current low budget it's not looking so good. My Ex- Fleet of Sixes these are all long gone! :bang: 1954 Customline 223 3 speed with O/D, 1963 Fairlane project drag car with BB6, 1977 Maverick 250 with C4, 1994 F-150 a 300 with 5 speed.

User avatar
B RON CO
VIP Member
Posts: 874
Joined: Tue Apr 05, 2016 7:02 pm
Location: Long Island, NY
Contact:

Re: Adjustment wheel all the way out with new cylinders & shoes

Post #56 by B RON CO » Sat May 23, 2020 5:11 pm

Hi, on the front drums, I would not loosen the adjustment. I know the scrape, no scrape you are talking about. I would adjust the shoes tighter, as long as the wheel still spins. The same on each side. When the shoes are adjusted up the pedal has very little travel.
Then drive it and if it feels good, leave it.
I have been known to bleed the brakes again, a week or so later, after using the car and guess what, you get a little more air that worked it's way through the system.
So if the brakes seem good after another adjustment, drive it a couple of weeks, then you can jack up a wheel, check the scrape scrape sound and do a final bleed. Hopefully all will be perfect.
Good luck
B RON CO. Still workin' on it!

1933 Ford Pickup - 59A Flathead V8
1966 Ford Bronco - U14 - 170/200 Straight 6
1966 Ford Mustang - 289 V8

Who is online

Users browsing this forum: No registered users and 4 guests