wheelzzs":1sk4ri31 said:
I am thinking about looking for an old granada for the disk break(5lug) setup for my 63 falcon. Will a granada rear end fit under the falcon as it will help determine how much a granada would be worth to me for parts. I want a 5 bolt lug setup as I hate 4bolts
Hi Wheelzzs,
This might be of some help.
1963 Falcon
A stock 63 falcon V8 is 56 inches, the narrowest 8" ford made.
63 Falcon 8" rear 56" wide
Measurements 56" wheel to wheel
74 Maverick 8" 56.50†inches
90, 91, 92 Ranger 8.8 Rears 56â€
Approximate rear end widths measured from backing plate to backing plate.
Add Width to compensate for drums as follows:
4" - 5" for small cars 5" - 6" for intermediate cars 6" - 8" for large cars
67 Mustang Six 52" - 53"
71-77 Mavericks
71 Comets
71-72 Pintos
66 Falcon 54" -55"
67 Mustang V-8
71 Torino 56" -57"
72 Cougar
STOCK CENTER TO CENTER SPRING PERCH DISTANCE
68 -71 Fairlane/Torino 42"
49-51 Ford
71 - 72 Pinto 42 1/2
67 Mustang 43"
70's Ford Grenada
71-77 Maverick 43 1/2"
69 Ford Van 51"
Donor Vehicles Front and Rear Suspension Width (Flange to Flange)
74-79 Ford Mustang II/Pinto & Mercury Capri/Bobcat 55 ½" 55 ½"
71-77 Ford Maverick with 8" axle 56 ½"
75-80 Ford Granada with 8" axle 57 ½"
64-66 Mustangs 57"
67-71 Mustang 59"
72-73 Mustang 60"
75-78 Granada 9" (43" perch to perch) 52 ¼"
75-78 Maverick 9" (43" perch to perch) 56 ¼"
81-87 Olds Cutlass 58 ½"
REAR SUSPENSION:
The following is a general list of rear ends and their dimensions to help narrow the search for a possible candidate to replace the torque tube rear end or just get a better set of gears for highway driving.
Advance Design Trucks seem to be using rear ends with widths ranging from 58"- 62". I'm not sure of the Task Force width ranges at this time.
Contributing information were Bob Welch, J Forbes and various locations throughout the Web and Automotive Magazines.
Rear Axle Measurements
MEASURED ACROSS WHEEL MOUNTING SURFACE
56 1/2"
71-77 Ford Mavericks 8",
57"
71-74 V-8 Mavericks 8" All
75-77 6's & 8's Maverick 5 Lug 8"
49-51 Ford, 57-59 Ford 9"
57 1/4"
64 1/2 - 65 Mustangs
58"
78-88 Mid sized GM Car, Malibu/Monte Carlo (82 up Metric Studs), 80 Granada & Lincoln Versailles,
67-70 Mustang/Cougar/Fairlane, Regal with 10 bolt axle, S-10 P.U., 65-67 Nova
58 1/2"
Ford Grenada
60"
55-64 71-73 Mustang/Cougar
Where to Find the Nine Inch Rear Axle
1967-1973 medium and big block Mustangs and Cougars
1966-1971 Fairlanes, Torino’s, Montego’s, Comets, and other Ford intermediates with big blocks.
1957-1959 V8 Fords and Mercury’s
1977-1981 Lincoln Versailles & Trucks
Types of Nine Inch Axle Housings
1967-1973 Mustang/Cougar - light duty, thinnest housing material, small axle bearings, 28 and 31 splines.
1957-1968 passenger car and 1/2 ton truck - medium duty, stronger than Mustang type, 28 and 31 splines. Ranchero/Torino - heavy duty thick wall housing, 3.25 inch diameter axle tubes with flat tops.
1969-1977 Galaxies (coils), Lincolns (coils), and late pickups (leaf) - 3.25 inch diameter all the way to the backing plate, coil housings have upper control arm mount
How to Recognize Nine Inch Housing Centers
1957 - No dimples, flat center band up the center of the rear cover, bottom drain plug.
1958-1959 - two dimples on back of housing, flat center band, some had drain holes.
1960-1967 - two dimples, flat center band, oil level hole in back cover.
1963-1977 Lincoln, LTD, Thunderbirds had 9.375 inch centers; housings were cut away at the gasket surface for ring gear clearance, one curved rib at the front top portion of differential, strong but no gears.
Tip on Shortening Nine Inch Axles
1972 and earlier 31 spline axles have the ability to be shortened.
28 spline axles are tapered and cannot be shortened and re-splined.
1973 and later cars have a 5-on-5 bolt circle and the axles cannot be shortened.
1967-1973 Mustang axles can be identified by wheel flange:
Oval hole = 28 splines.
Two large holes and counter-sunk center = 31 splines.