Hi Everyone, first time posting. I couldn't figure out how to find a forum this question fit better in than the Introductions. My timing jumped a tooth. Chain had some slack so I ordered a new set, the camshaft sprocket fits fine but the crankshaft sprocket is about 3-4mm to small. I ordered 3 sets thinking the first one could have been a miss-box, one Cloyes C3026K and also a Comp Cams 3223. All had the same issue. I am at a loss with how to find the right timing set/crankshaft gear. I considered reusing the gears and trying to find a place that can order a chain. Could there be another crankshaft in the engine and that's why these don't fit? am I missing something? I'm going to try to upload a few pictures (see the links at the bottom, let me know if there is a better way to share them) and hopefully one of you guys can see or identify something about the engine as to why the timing sets I'm ordering don't seem to fit.
I have a 1967 falcon cylinder that has a '69 6 cylinder in it I believe is a 200ci due to the 5 freeze plugs. Stamp on the block is C9DE 6015-B and another spot has 9J29. I would appreciate any help or advice.
Below are the measurements of the old and new crankshaft sprockets. Let me know what additional info or pictures I can provide to help. Thanks in advance!
Original Crankshaft Sprocket - 35mm Inside diameter, 64mm outside diameter, 21 teeth
New Crankshaft Sprocket - 32mm Inside diameter, 58mm outside diameter, 19 teeth. I’m not concerned about the difference in teeth or outside diameter, should I be? But if the inside diameter is too small I can’t get it on the crankshaft.
http://u.cubeupload.com/MM_Falcon/20200826160138.jpg
http://u.cubeupload.com/MM_Falcon/20200916202835.jpg
http://u.cubeupload.com/MM_Falcon/20200916203529.jpg
http://u.cubeupload.com/MM_Falcon/20200916203858.jpg
http://u.cubeupload.com/MM_Falcon/20200916203905.jpg
http://u.cubeupload.com/MM_Falcon/20200826160144.jpg
http://u.cubeupload.com/MM_Falcon/20200904230406.jpg
http://u.cubeupload.com/MM_Falcon/20200916202548.jpg
http://u.cubeupload.com/MM_Falcon/20200916202603.jpg
I have a 1967 falcon cylinder that has a '69 6 cylinder in it I believe is a 200ci due to the 5 freeze plugs. Stamp on the block is C9DE 6015-B and another spot has 9J29. I would appreciate any help or advice.
Below are the measurements of the old and new crankshaft sprockets. Let me know what additional info or pictures I can provide to help. Thanks in advance!
Original Crankshaft Sprocket - 35mm Inside diameter, 64mm outside diameter, 21 teeth
New Crankshaft Sprocket - 32mm Inside diameter, 58mm outside diameter, 19 teeth. I’m not concerned about the difference in teeth or outside diameter, should I be? But if the inside diameter is too small I can’t get it on the crankshaft.
http://u.cubeupload.com/MM_Falcon/20200826160138.jpg
http://u.cubeupload.com/MM_Falcon/20200916202835.jpg
http://u.cubeupload.com/MM_Falcon/20200916203529.jpg
http://u.cubeupload.com/MM_Falcon/20200916203858.jpg
http://u.cubeupload.com/MM_Falcon/20200916203905.jpg
http://u.cubeupload.com/MM_Falcon/20200826160144.jpg
http://u.cubeupload.com/MM_Falcon/20200904230406.jpg
http://u.cubeupload.com/MM_Falcon/20200916202548.jpg
http://u.cubeupload.com/MM_Falcon/20200916202603.jpg