All Small Six The Ford Small Six Tech Info & Sticky Section (Use These Links For Your Info & Research)

This relates to all small sixes
Status
Not open for further replies.
bubba22349

bubba22349

Top Poster
VIP
Supporter 2021
Supporter 2019
Departed Member
200 Dyno Test Results and Discussion this also has some very good info on 3 X 1V Offy & Eldenbrock Tri Carb Power Tuning

200ci - Seriously disappointing dyno numbers

I grenaded the camshaft on this engine about ten years ago, rebuilt it shortly thereafter, and finally got the rest of the car reassembled late last summer. The new build has a bit over 1000 miles on it now, runs and feels good, no driveability problems other than a fairly lopey idle. 200ci...
fordsix.com fordsix.com
 
Last edited:

All Small Six - Tri-Power Carburetor Options?

Looking for a little advice for my next steps. I was able to purchase a Offy manifold that came with three Holley 1904’s, I also have on the shelf two Carter YFA’a. Which would be the better set up, the Holley’s or Carter’s? (I have a 200ci, large log) The center Carter would have a hot air...
fordsix.com fordsix.com
 

All Small Six - Tri-power tuning

Well after 100 miles of easy driving finally took the Falcon in to the local chasis dyno to get some baseline numbers for tuning. Glad I did.. Founf that I was running way to lean 14.8-15.2 A/F ratio. My cruise ratio numbers where decent 12.5-12.8 off the primary carb, but as soon as we tried to...
fordsix.com fordsix.com
 

six barrel econo Log

viewtopic.php?f=22&t=72509&p=557400#p557400 Thanks for your support bubba. Multiple carbs and the turbo WILL be done. The question now is will it be two or three. I believe I will start a new post and hope for some input from Dean. And Rich, I absolutely love your idea of swapable/removable...
fordsix.com fordsix.com
 

DUI Distributor Shaft & Bushings Binding From Lack 0f Lub.

Any one running a DUI distributor should be aware of insufficient oiling to the distributor shaft & bushings. I just received & modified another distributor to fix this problem again. The customer was not aware his distributor was very close to being seized. Anyone running a DUI should remove it...
fordsix.com fordsix.com
 

HEI Upper Shaft Oiling + Distributor Gear Extra Oiling

If you own a HEI distributor you might have upper shaft oiling concerns. The modification to fix this problem also benefits extra distributor gear oiling in addition to the oiling groove done to #2 & #3 lifters. This modification involves complete dissembling the HEI to fix this condition. That...
fordsix.com fordsix.com
 

Extra Oil Supply To Distributor Gear

This mod will supply the distributor gear extra oiling. This mod applies only to the second & third lifters only. This allows more oil to the orifice in the block over the distributor & camshaft gears.
fordsix.com fordsix.com
 
Last edited:

200ci - Alternative 200 six connecting rod

We had a joint effort looking for an aftermarket rod for the 200 and drag-200stang found that the Toyota 1JZ rod would be a good candidate. 4.931" center to center 2.166" BE bore for the 2.047" crank pin 1.020" BE Width 1.00 PE width. 22mm pin Comes in sets of six.
fordsix.com fordsix.com
 

All Small Six - yellow terra rocker arm install tips

When you install the yella-terra rocker arms you starve the distributor gear & camshaft gear of very needed lubrication. To fix that condition the second & third lifters are on either side of the oil hole above the gears. You can cut a .025" x .025" groove in those two lifters and that will...
fordsix.com fordsix.com
 

Roller timing chain for 250

Well. I can't say that this has been an easy path to travel,...and I'm still not there yet, but there is a light at the end of the tunnel. I decided to copy Does10's method of making a roller chain for a SBF work on a 250. So I went out and bought a true roller set from Summit under their brand...
fordsix.com fordsix.com
 

SBF timing set installed on Kelly's 250!

Well it looks like this is going to work! Kelly's shortblock is reassembled! It's not running yet, but will be in a few weeks. She races again Labor Day Weekend. I've been at this for awhile waiting patiently for my machine shop to finish up the required machine work. Anyway here's what I did...
fordsix.com fordsix.com
 

All Small Six - Flow testing the "log" heads

Over the past few years we've flow tested several Australian 250-2V cylinder heads, as well as our own Aluminum cylinder heads. However we've always wondered how the cast iron "log heads" stacked up, not only to the Australian and Aluminum heads, but to each other, both in stock and modified...
fordsix.com fordsix.com
 

All Small Six - Small Six Tech (sticky's)

We were getting so many STICKY's that I decided to condense them into one thread. If you come across a good topic that should be added to the list, just post a request below. Make sure you include the topic title and the link. Then one of the moderators can check it out and add to the list if...
fordsix.com fordsix.com
 
Echo -1955 Rebuild's His 1965 Mustang 200 I6 Block.

200ci - Echo -1955 Rebuild's His 1965 Mustang 200 I6 Block.

Rebuild 65 200 I6 Block. I bought my 65 in 65. I brought it back to life in 98. I had to repaint it a couple months ago because my prized 100 lb Lab played catch me iffen ya can wid a 10 lb cat. Their playground was the top of my FB. Scratched the paint all the way down to metal. This is where...
fordsix.com fordsix.com
 
Status
Not open for further replies.

Similar threads

Baxsie
  • Sticky
Modifying the Holley HyperSpark distributor 565-315 (made for the "small block") to work with a "big block" Ford 240 six or 300 six (with Holley ECMs)
3 4 5
Replies
88
Views
15K
bangstk
bangstk
Frankenstang
  • Locked
T-5 Conversion Swap for a 200 1966 Block with a 1967 Bell
2
Replies
32
Views
36K
Frankenstang
Frankenstang
xctasy
Mikey: Death of the best 350 and 500 for a six...the #2305
Replies
19
Views
2K
xctasy
xctasy
Back
Top