Click Here -> Please Consider Making a PayPal Contribution to the FordSix Forum!
2019 Contributors:
NJwpod, 1strodeo, mightynorseman, maxtrux, 6d7coupe, broncr, Phase3, 68Flareside240, bmbm40, mustang6, WorldChampGramp, justintendo, BigBlue94, ags290, motorsickle1130, Rooster, ousooner919, ethanperry, rzcrisis, DoctorC, jamyers, Motorboy, fastpat, Silverback280, chad, drag-200stang, THE FRENCHTOWN FLYER, Jimmys61falcon, rjonah, Sooshi, Robert92867, Invectivus


PLEASE TEST ON http://dev.fordsix.com

<<<***PLEASE READ*** New Site Update >>>

‘74 250 - timing chain - how much slack is acceptable?

Moderator: Mod Squad

User avatar
62Ranchero200
Registered User
Posts: 476
Joined: Fri May 18, 2012 10:38 am
Location: Houston, TX
Contact:

‘74 250 - timing chain - how much slack is acceptable?

Post #1 by 62Ranchero200 » Sun Mar 22, 2020 10:08 am

My 250 has about 10,000 miles on it. Pulled the old cam out last night, and timing chain can be deflected about 1/2”. There are no wear marks and everything otherwise looks good. Gearset with chain were new when engine was built six years ago.

Is this ok?

Thanks
Bob
62 Ranchero, 252 cid, 300 rods, RaceTek pstns, ARP mains bolts & studs, balanced & blueprinted, CI AL head, 1.6 adj rckrs, Smith Bros, 274/274/108 cam, CI int, Holley 500, DSII, CI SS hdrs, PowerMaster strtr and 1wire alt, Optima, V8 rad, T-5z, 10" organic clutch, 5 lug 8" w/3.80 Trac Loc, rear drums, front 5 lug discs, Centerlines. Next: ?.

User avatar
chad
Registered User
Posts: 5127
Joined: Sat Oct 24, 2009 9:51 am
Location: Lawrence Swamp, S. Amherst, MA

timing chain - how much slack is acceptable?

Post #2 by chad » Sun Mar 22, 2020 11:24 am

"... how much slack is acceptable?..."
my eye & fingers say 'none'. Sorry don't
have a 'deflection measurment' ona dial
indicator. If I could move it a 1/2 inch I'd
start over...look at other 'looseness'.
"Big thing is only make one change at a time. Change 2 or more things at a time it becomes difficult to figure which change helped or hurt" turbo2256b » 1/16/2017
Chad - '70 LUEB on '77 frame (i.e. PS, D44, trapezoidal BB 9", 4.11), '69 250ci, NV 3550 & DSII, "T" D20/PTO, 2" SL, 1" BL, 4 discs, 33"X15", tool boxes, etc. Seeking: Hydraulic gear motor for Koenig pto. chrlsful@aol.com (413) 259-1749

User avatar
wsa111
FSP Moderator
Posts: 3422
Joined: Sat Jan 24, 2004 5:28 pm
Location: South Carolina
Contact:

Re: ‘74 250 - timing chain - how much slack is acceptable?

Post #3 by wsa111 » Sun Mar 22, 2020 12:15 pm

Since its not a roller chain, replace it. If gears show wear do the same.
67 mustang,C-4, with mod. 80 hd, custom 500 cfm carb with annular boosters, hooker headers, dual exh.-X pipe, flowmaster mufflers, DSII dist. MSD-6425CL & MSD-Blaster 8252 Coil. Engine 205" .030" over with offset ground crank & 1.65 roller rockers. 9.5 comp., Isky 262 cam.
2003 Ford Lightning daily driver. Recurving Distributors. billythedistributorman@live.com
Image

CZLN6
VIP Member
Posts: 3347
Joined: Fri Nov 15, 2002 11:07 am
Location: Idaho Falls, Id
Contact:

Re: ‘74 250 - timing chain - how much slack is acceptable?

Post #4 by CZLN6 » Sun Mar 22, 2020 4:03 pm

Howdy Bob and All:

Since you have it apart, replacing the chain is cheap insurance. You said the current chain has 1/2" of slack, or deflection, check the new chain for comparison. And let us know. You might also do some testing on how many degrees of cam movement between the two points of slack. Chain slack, due to wear, causes the cam to act like it is being retarded. That is not near as bad as if it is being advanced- for performance. Chain slack, as the engine accelerates and decelerates causes wear to the cam gears.

Also check your rocker arm shaft to make sure that oil is getting to the front rocker arm and draining freely down.

Keep it coming.

Adios, David
co-author of the Falcon Performance Handbook
http://www.falcon6handbook.com/

Who is online

Users browsing this forum: my way and 17 guests